Hiw to bypass battery guard by intellitec software#
Hiw to bypass battery guard by intellitec Pc#

Hiw to bypass battery guard by intellitec software#

The Graphical User Interface software is windows based and is supplied free of charge after the installation engineer has been on an Intellitec certified course. The software has been designed to be user friendly and the amount of parameters that can be programmed is almost endless. Your ignition signal for the BIM can be taken from the BIRD control. Doctor 125A Side Mount Compact Battery Disconnect Switch with Fused Bypass (20310) 0. The battery cover shows a picture of it but its not out in the open where you can see it. Intellitec Battery Disconnect Switch 100 Amp - 01-00335-000. Then run short cables from each side of the isolation solenoud to the BIM or short cables directly from each battery bank, to the BIM, If close by. Intellitec 100A Battery Disconnect Switch (01-00335-000). If the battery voltage drops below 12. You can simply disable the isolator by removing 1 small wire on the isolation solenoid. There are also two programmable 10A outputs that can be used to switch external alarms or indeed what ever may be specified. Battery Guard 2000 constantly monitors the available battery power when the engine or charging system is off. To restart, simply press the reset switch and starting power is restored.Īutomatic reconnection is also possible in specific applications via the software.īuilt into the Battery Guard 3000 is a programmable audible alarm, this can be linked to both voltage and time. NOTE: Battery Guard is a battery charge saving device used to automatically switch off the battery in the event of a low charge condition while the ignition. This ensures that starting power is preserved. The Battery Guard 1000 prevents 'dead batteries' by disconnecting the battery before it is completely drained and cannot start the vehicle or cause damage to.

If the battery voltage drops below a pre programmed level of both time and voltage, the system isolates all electrical loads that are connected through the battery guard relay. The software has been designed to be very user friendly, the amount of parameters that can be programmed is almost endless.The Battery Guard 3000 is a fully programmable power management system.īattery Guard 3000 operates by constantly monitoring the available battery power when the engine or charging source is not active.Ĭut out voltage`s, timers & alarms are fully programmable to provide a fully flexible solution. If the battery voltage drops below 12.1V a voltage sensitive timer is triggered within the ECU. Experienced in electric vehicle technology, our Engineering team are ready to demonstrate how the Intellitec Battery Guard range continues to provide excellence in battery power protection for EV.

Hiw to bypass battery guard by intellitec Pc#

The GUI software is windows based and is supplied by Intellitec after the installation engineer has been on a certified training course.Ĭommunication from PC to the Battery Guard ECU is via RS232. Battery Guard 2000 constantly monitors the available battery power when the engine or charging system is off. Intellitec is a global leader in Battery Management, Electronic Monitoring and Multiplex systems. This allows the OEM / fleet operator to provide different levels and frequency of alarms to suit each specific application.īattery Guard 3000+ is also an intelligent split charge system, simply by adding a holding relay to the system, the rest is a simple matter of programming the system to operate to the customer spec.Īs the system is fully programmable, we can ensure that the system can be integrated into the vehicles electrical system and not cause any conflict or warranty issues on ECU’s.īuilt into the software is some limited logging capabilities, we record every low voltage event, this information can be useful for fleet engineers. There is also 2 programmable 10A outputs that can be used to switch external alarms or indeed what ever the electrical engineer or fleet engineer may specify. INTELLITECS BATTERY GUARD system prevents 'dead batteries' by disconnecting the battery before it is completely drained and cannot start the vehicle. Automatic reconnection of power is also possible in specific applications via software.īuilt into the electronics is a programmable audible alarm, this can be linked to both voltage and time. Press the reset switch and power for starting is restored. Name: intellitec battery disconnect relay wiring diagram. When the battery is isolated due to low voltage, this is recorded in the Battery Guard ECU, this information is useful to fleet operators. You probably have converter/charger power on one side of the relay and battery power on the other.

If the battery voltage drops below a pre-determined programmed level of both time & voltage, the system isolates all the electrical loads that are wired through the Intellitec contactor, to guarantee starting power. NO MORE FLAT BATTERIES WITH BATTERY GUARD 3000!īattery Guard 3000+ operates by constantly monitoring the available battery power when the engine or charging source is not running.